Items Included• 1 Lower Skid Valance Shellz Overlay
• Preinstalled 3m Tape • 1 Adhesion Promoter Packet |
Tools Required• Isopropyl Alcohol
• Clean Cloth |
Before You Get Started...
Warm surfaces and 3M tape with heat gun if ambient temperature is below 68 degrees F
|
Any Modification or unintended use will void the manufacturers warranty
|
A dry fit of all pieces must be performed before the final installation of the product to ensure fit
|
Products cannot be returned for a full refund after the red backing to the 3M tape is removed
|
Preparation
The degree to which you follow these preparation instructions will determine the quality of the installed product. Please follow all instructions and be patient. If you are unsure of any area of the installation after reading these instructions, please call us at 844-918-3688 (EXT 3) and we will answer any questions that you have.
Installation
NOTE: Dry-Fit all BumperShellz pieces to their specific locations BEFORE removing ANY of the red backing strips from the tape. Make sure all pieces are correct, i.e., you have received all pieces shown above, color/pattern is correct, and that all are undamaged. There should not be any (or extremely minimal) bumper surface visible once the bumper cover is placed on the bumper. Dry Fitting is also good practice for lining up each piece and guiding it into place, visualizing how to do it when the backing strips are removed, and the tape is STICKY. Note that once the backing is removed, we cannot give full credit for return.
1. Dry-fit your Lower Bumper Skid Plate Valance by following the instructions below without removing the backing to the 3M double-sided tape. Ensure the part is centered, and make note of its positioning for reference later.
2. Ensure the bumper is clean and free of debris. Use Isopropyl rubbing alcohol to free the bumper surface of any chemicals or soap residue that may limit the effectiveness of the 3M tape. Apply the adhesion promoter stick along all areas of the bumper where the 3M tape will be touching down.
2. Ensure the bumper is clean and free of debris. Use Isopropyl rubbing alcohol to free the bumper surface of any chemicals or soap residue that may limit the effectiveness of the 3M tape. Apply the adhesion promoter stick along all areas of the bumper where the 3M tape will be touching down.
Clean lower bumper trim thoroughly with Isopropyl alcohol and a clean cloth
|
Apply your adhesion promoter where the 3m tape will be touching down.
|
3. Peel all the backing completely to all of the upper pieces of 3M tape. On the lower strip of tape, peel and tape the first 1" of backing to the 3M tape to the front for easy access later. Refer to the images below for instruction.
3a. Remove all backing to the upper portions of tape. Only the lower strip of tape will not be completely removed.
3b. On the lower strip of tape, peel back the red 3m 1" and wrap it around to the front.
|
3c. Secure the red tape to the front with masking tape. Repeat this process on the opposite side.
|
4. Now it is time to install the overlay on the OEM part. Begin on one side of the lower front bumper trim. Be careful not to let the tape touch down until the applique is centered, and you are happy with its position. (If your model has a protective film on the surface, peel back the area that will be tucked under the tailgate cap.) Continue down the part, applying pressure as you go.
5. Remove the backing to the 3m tape along the lower section of the overlay. Apply firm pressure as you move along.
**ONLY IF YOU HAVE PROTECTIVE FILM** Remove the protective film from the overlay.
Care for your BumperShellz™
Care for your BumperShellz™ like you would any fine paint finish. Use high quality cleaning products designed specifically for car care.
Gloss finishes: Oftentimes, minor scratches can be buffed out on the gloss finishes. Rubbing compounds can be used with a mechanical buffer, for deeper scratches.
Matte finishes are much more susceptible to abrasions, leaving a "glossy sheen" on the finish, which are generally permanent. Do not attempt to buff out scratches/abrasions on your matte finish, as this will generally make the damage worse. Avoid excessive friction when trying to remove anything stuck to the matte finish surface and keep cleaning rags/water clean and abrasive free. Abrasive brush-type car washes are not recommended, as they can abrade the Matte finish. Brushless car washes are acceptable.
NOTE for Maximum Adhesion: The acrylic foam tape used to adhere your BumperShellz is “pressure sensitive”, so making sure there is sufficient pressure applied to each of the taped areas is vital to achieve optimum adhesion of your BumperShellz™ to your bumper. It is also recommended that you come back a few hours later, or the next day, to give each BumperShellz piece another pressure rub to ensure the best adhesion. Allow the tape adhesive to set up for at least 24 hours before washing your truck. Maximum adhesion is reached after 3-5 days in temperatures above 70 degrees, longer if it is cooler. Once the adhesive has fully bonded to a properly prepared bumper surface, it is nearly impossible to remove the BumperShellz without damaging them. Please refer to “removal instructions” in the BumperShellz FAQ section on the website, should removal be necessary.
Gloss finishes: Oftentimes, minor scratches can be buffed out on the gloss finishes. Rubbing compounds can be used with a mechanical buffer, for deeper scratches.
Matte finishes are much more susceptible to abrasions, leaving a "glossy sheen" on the finish, which are generally permanent. Do not attempt to buff out scratches/abrasions on your matte finish, as this will generally make the damage worse. Avoid excessive friction when trying to remove anything stuck to the matte finish surface and keep cleaning rags/water clean and abrasive free. Abrasive brush-type car washes are not recommended, as they can abrade the Matte finish. Brushless car washes are acceptable.
NOTE for Maximum Adhesion: The acrylic foam tape used to adhere your BumperShellz is “pressure sensitive”, so making sure there is sufficient pressure applied to each of the taped areas is vital to achieve optimum adhesion of your BumperShellz™ to your bumper. It is also recommended that you come back a few hours later, or the next day, to give each BumperShellz piece another pressure rub to ensure the best adhesion. Allow the tape adhesive to set up for at least 24 hours before washing your truck. Maximum adhesion is reached after 3-5 days in temperatures above 70 degrees, longer if it is cooler. Once the adhesive has fully bonded to a properly prepared bumper surface, it is nearly impossible to remove the BumperShellz without damaging them. Please refer to “removal instructions” in the BumperShellz FAQ section on the website, should removal be necessary.