Items Included• Center BumperShellz™ - TuffShellz™ Textured ABS, with High Strength Acrylic Foam Tape (pictured part may be different)
|
|
Tools Required• Plastic Prying/Trim Tool
|
Before You Get Started...
Warm surfaces and 3M tape with heat gun if ambient temperature is below 68 degrees F
|
Any Modification or unintended use will void the manufacturers warranty
|
A dry fit of all pieces must be performed before the final installation of the product to ensure fit
|
Products cannot be returned for a full refund after the red backing to the 3M tape is removed
|
PREPARATION
1. BumperShellz™ are secured using the highest quality 3M Auto-Grade tape. The optimal temperature for installation is between 68°F and 100°F. If the ambient temperature is below 68°F use a heat gun or hair dryer to warm the bumper and 3M tape immediately prior to installation.
2. Ensure the surface is clean. After a quick wash use Isopropyl alcohol lint-free cloth to clean the surface thoroughly. For professional results use 3M brand prep solvent 70, Adhesion Promoter 94, or a similar vinyl adhesion promoter product.
3. Dry fit all parts before removing 3M tape to check for fitment and practice the installation method before the attachment is permanent.
The degree to which you follow these preparation instructions will determine the quality of the installed product. Please follow all instructions and be patient. If you are unsure of any area of the installation after reading these instructions, please call us at 844-918-3688, and we will answer any questions that you have.
2. Ensure the surface is clean. After a quick wash use Isopropyl alcohol lint-free cloth to clean the surface thoroughly. For professional results use 3M brand prep solvent 70, Adhesion Promoter 94, or a similar vinyl adhesion promoter product.
3. Dry fit all parts before removing 3M tape to check for fitment and practice the installation method before the attachment is permanent.
The degree to which you follow these preparation instructions will determine the quality of the installed product. Please follow all instructions and be patient. If you are unsure of any area of the installation after reading these instructions, please call us at 844-918-3688, and we will answer any questions that you have.
Installation
1. Peel red backing off tape strips on back surface of your BumperShellz™ – TuffShellz™ Center Cover
2. Center the cover on your bumper and tuck the top flange under the step trim, using your non-scratching pry tool to slightly lift the trim/step pad by wedging it under the trim just enough to slide the BumperShell in to place; like using a shoehorn. Try not to allow the tape to contact the bumper until the cover is in its proper position.
NOTE: A silver mark has been placed to indicate the centerline of your TuffShellz center cover. Try to align this mark with the center of the bumper before pressing the tape against the bumper
3. Tuck the remaining flange length under the trim by gently and progressively lifting the edge of the trim just enough to slide the flange underneath. Do not use excessive force, as this may damage your BumperShellz™ and/or trim. If the cover is not going on with reasonable effort, the flange is probably hung up somewhere.
4. Once in proper position, press the BumperShellz firmly against the bumper on the taped areas for at least 30 seconds to make sure tape adheres to the bumper.
|
|
|
NOTE for Maximum Adhesion: The acrylic foam tape used to adhere your BumperShellz is “pressure sensitive”, so making sure there is sufficient pressure applied to each of the taped areas is vital to achieve optimum adhesion of your BumperShellz™ to your bumper. It is also recommended that you come back a few hours later, or the next day, to give each BumperShellz piece another pressure rub to ensure the best adhesion. Allow tape adhesive to set up for at least 24 hours before washing your truck. Maximum adhesion is reached after 3-5 days in temperatures above 70 degrees; longer if it is cooler. Once adhesive has fully bonded to a properly prepared bumper surface, it is nearly impossible to remove the BumperShellz without damaging them. Please refer to “removal instructions” in the BumperShellz FAQ section on the website, should removal be necessary.
Care for your BumperShellz™
Care for your BumperShellz™ like you would any fine paint finish. Use high quality cleaning products designed specifically for car care.
Gloss finishes: Oftentimes, minor scratches can be buffed out on the gloss finishes. Rubbing compounds can be used with a mechanical buffer, for deeper scratches.
Matte finishes are much more susceptible to abrasions, leaving a "glossy sheen" on the finish, which are generally permanent. Do not attempt to buff out scratches/abrasions on your matte finish, as this will generally make the damage worse. Avoid excessive friction when trying to remove anything stuck to the matte finish surface and keep cleaning rags/water clean and abrasive free. Abrasive brush-type car washes are not recommended, as they can abrade the Matte finish. Brushless car washes are acceptable.
Gloss finishes: Oftentimes, minor scratches can be buffed out on the gloss finishes. Rubbing compounds can be used with a mechanical buffer, for deeper scratches.
Matte finishes are much more susceptible to abrasions, leaving a "glossy sheen" on the finish, which are generally permanent. Do not attempt to buff out scratches/abrasions on your matte finish, as this will generally make the damage worse. Avoid excessive friction when trying to remove anything stuck to the matte finish surface and keep cleaning rags/water clean and abrasive free. Abrasive brush-type car washes are not recommended, as they can abrade the Matte finish. Brushless car washes are acceptable.
