Ecoological - Truck Aftermarket Accessories
  • Home
  • Products
    • GapShield
    • AeroBox
    • BumperShellz
  • SALE ITEMS
  • 2022+ Tundra BumperShellz
  • New Model Request
  • Become A Retailer
  • Contact Us
  • Manufacturing
  • About Us
  • Videos
  • Toyota Color Match Wait list
  • Installation Instructions Home
    • FORD MODEL YEAR SELECT >
      • 2015-2017 Ford F-150 Installation Instructions Home
      • 2018-2020 Ford F-150 Installation Instructions Home
      • 2017-2019 Ford F-250 Installation Instructions Home
    • CHEVROLET MODEL YEAR SELECT >
      • 2007-2013 Silverado Installation Home
      • 2014-2015 Silverado Installation Home
      • 2016-2018 Silverado Installation Instructions Home
      • 2019-2022 Installation Home >
        • 2019-2021 Front Bumper Installation Home
    • GMC MODEL YEAR SELECT >
      • 2007-2013 GMC Sierra Installations Home
      • 2014-2015 Sierra Installation Home
    • 2016-2018 Sierra Installation Home
    • RAM MODEL YEAR SELECT >
      • 2009-2012 RAM Installation Configuration
      • 2013-2018 RAM Installation Configuration
    • TOYOTA MODEL YEAR SELECT >
      • Tundra Installation Configuration >
        • Tundra Installation Version Selector Page
  • AeroBox Version Installation Selector
  • AeroBox Waitlist
  • Barcelona Red Sign-Up

2016-2018
Chevy Silverado
Front BumperShellz™ Installation Guide

​Predicted Installation Time: 30-40 minutes

Items Included

• Left, Right, and Center BumperShellz™

Tools Required

• Isopropyl Alcohol/clean rags
• 7mm socket/wrench/extension
​• Plastic pry/trim tool

Before You Get Started...

Picture
Warm surfaces and 3M tape with heat gun if ambient temperature is below 68 degrees F
Picture
Any Modification or unintended use will void the manufacturers warranty
Picture
A dry fit of all pieces must be performed before the final installation of the product to ensure fit
Picture
Products cannot be returned for a full refund after the red backing to the 3M tape is removed

Paint Preparation Instructions Link

If you ordered the "Paintable" version, click on the instructions link above for paint prep, and trim installation instructions.

Preparation

​Make sure your bumper is clean, dry, and free of debris.  Use a cleaner that will remove oil/grease to clean bumper surface, followed by wiping the bonding surface areas of your bumper thoroughly with regular isopropyl rubbing alcohol and a clean lint-free white cotton rag or clean disposable toweling. Do not use shop rags which may have dirt or oily residues. For superior results use 3M brand Prep Solvent 70 or similar products available at many auto stores.

Installation

NOTE: We recommend Dry-Fitting all BumperShellz pieces to their specific locations BEFORE removing ANY of the red backing strips from the tape. Make sure all pieces are correct, i.e., you have received all pieces shown above, with or without sensor holes and/or fog lamp openings, color/pattern is correct, and that all are undamaged. There should not be any (or extremely minimal) bumper surface visible once flanges are slid under trim and sensor holes (if present) are centered over sensor trim. Dry Fitting is also good practice for lining up each piece and guiding it into place, visualizing how to do it when the backing strips are removed and the tape is STICKY. Note that once the backing is removed we cannot give full credit for return.
1. Detach entire lower valance panel using 7mm socket to remove screws.




​2. Start with either left or right BumperShell and peel red backing off tape strips on the back surface. 
Picture
3. Wrap the outboard corner of the BumperShell around the corner flange of the bumper and rotate into position, being careful to not let the taped areas contact the bumper.





​
​
4. If bumper has parking sensors and/or fog lamps, adjust the position of the BumperShell to center the sensor within the clearance hole and fog lamp within the fog lamp opening before pressing down on the tape.
​NOTE: If the BumperShell is not going on with reasonable effort, do not use excessive force.  A flange is probably hung up somewhere and will need to be tucked in to place before proceeding.
Picture
5. Once in proper position, press BumperShellz™ firmly against bumper on taped areas from inboard-to-outboard for at least 30 seconds to make sure tape adheres to bumper. Repeat process for opposite side​
6. Remove red backing from tape strips on center section and position over bumper, centered between the two ends.  Offset flanges on either end of center section should overlap inboard edges of left and right BumperShellz™ and the “gaps” on overlapping flanges should be the same when installed correctly. Again, if sensor holes are present, ensure these are positioned correctly first.​
Picture
7. When satisfied the Center BumperShell is properly positioned, press taped areas against bumper as before, also making sure firm pressure is used to bond the overlapped joints together
​

​
​8. Reinstall/tighten the screws to secure lower valence panel, sandwiching lower BumperShellz™ tabs in between. If screw hole on the bumper covers have become offset, carefully use a drill, or circular file to widen screw holes appropriately.
Picture
NOTE for Maximum Adhesion: The acrylic foam tape used to adhere your BumperShellz is “pressure sensitive”, so making sure there is sufficient pressure applied to each of the taped areas is vital to achieve optimum adhesion of your BumperShellz™ to your bumper.  It is also recommended that you come back a few hours later, or the next day, to give each BumperShellz piece another pressure rub to ensure the best adhesion. Allow the tape adhesive to set up for at least 24 hours before washing your truck. Maximum adhesion is reached after 3-5 days in temperatures above 70 degrees, longer if it is cooler. Once the adhesive has fully bonded to a properly prepared bumper surface, it is nearly impossible to remove the BumperShellz without damaging them. Please refer to “removal instructions” in the BumperShellz FAQ section on the website, should removal be necessary.
Picture

Care for your BumperShellz™

Care for your BumperShellz™ like you would any fine paint finish.   Use high quality cleaning products designed specifically for car care.

Gloss finishes: Oftentimes, minor scratches can be buffed out on the gloss finishes.  Rubbing compounds can be used with a mechanical buffer, for deeper scratches.
​
Matte finishes are much more susceptible to abrasions, leaving a "glossy sheen" on the finish, which are generally permanent.  Do not attempt to buff out scratches/abrasions on your matte finish, as this will generally make the damage worse.  Avoid excessive friction when trying to remove anything stuck to the matte finish surface and keep cleaning rags/water clean and abrasive free.  Abrasive brush-type car washes are not recommended, as they can abrade the Matte finish.  Brushless car washes are acceptable.

Picture

    Show off your truck, WIN a GAPSHIELD

    Send us your Before and After Pictures!  We will show off your truck to the world.  Plus, one winner will be randomly selected each month to receive a free GapShield!  If you'd like us to tag you on Instagram, please include your profile name.
    Max file size: 20MB
    Max file size: 20MB
Submit

Contact Us

Contact Ecoological

Support

Shipping Information
Privacy Policy
Warranty & Return Policy
Terms & Conditions
​© 2023 Ecoological. All rights reserved.

3860 Cincinnati Ave 
Rocklin , CA 95765
  • Home
  • Products
    • GapShield
    • AeroBox
    • BumperShellz
  • SALE ITEMS
  • 2022+ Tundra BumperShellz
  • New Model Request
  • Become A Retailer
  • Contact Us
  • Manufacturing
  • About Us
  • Videos
  • Toyota Color Match Wait list
  • Installation Instructions Home
    • FORD MODEL YEAR SELECT >
      • 2015-2017 Ford F-150 Installation Instructions Home
      • 2018-2020 Ford F-150 Installation Instructions Home
      • 2017-2019 Ford F-250 Installation Instructions Home
    • CHEVROLET MODEL YEAR SELECT >
      • 2007-2013 Silverado Installation Home
      • 2014-2015 Silverado Installation Home
      • 2016-2018 Silverado Installation Instructions Home
      • 2019-2022 Installation Home >
        • 2019-2021 Front Bumper Installation Home
    • GMC MODEL YEAR SELECT >
      • 2007-2013 GMC Sierra Installations Home
      • 2014-2015 Sierra Installation Home
    • 2016-2018 Sierra Installation Home
    • RAM MODEL YEAR SELECT >
      • 2009-2012 RAM Installation Configuration
      • 2013-2018 RAM Installation Configuration
    • TOYOTA MODEL YEAR SELECT >
      • Tundra Installation Configuration >
        • Tundra Installation Version Selector Page
  • AeroBox Version Installation Selector
  • AeroBox Waitlist
  • Barcelona Red Sign-Up